Attribute Values: I

IKO LRB141816 LRB - SERIES

IKO LRB202420 LRB - SERIES

IKO LRB243020 LRB - SERIES

IKO LRB324028 LRB - SERIES

IKO LRB364424 LRB - SERIES

IKO LRB384828 LRB - SERIES

IKO LRB445232 LRB - SERIES

IKO LRB526032 LRB - SERIES

IKO LRT121612 LRT - SERIES

IKO LRT121622 LRT - SERIES

IKO LRT12514060

IKO LRT12514060 LRT - SERIES

Iko Lrt15016540

IKO LRT15016540

IKO LRT15016540 LRT - SERIES

IKO LRT17019060

IKO LRT17019060 LRT - SERIES

IKO LRT172116 LRT - SERIES

IKO LRT172213 LRT - SERIES

IKO LRT172226 LRT - SERIES

IKO LRT18020569

IKO LRT18020569 LRT - SERIES

IKO LRT202516 LRT - SERIES

IKO LRT202520 LRT - SERIES

IKO LRT202526 LRT - SERIES

IKO LRT222616 LRT - SERIES

IKO LRT222817 LRT - SERIES

IKO LRT24026580

IKO LRT24026580 LRT - SERIES

IKO LRT252920 LRT - SERIES

IKO LRT303516 LRT - SERIES

IKO LRT303526 LRT - SERIES

IKO LRT303530 LRT - SERIES

IKO LRT324036 LRT - SERIES

IKO LRT354020 LRT - SERIES

IKO LRT354220 LRT - SERIES

IKO LRT360400118

IKO LRT360400118 LRT - SERIES

IKO LRT404530 LRT - SERIES

IKO LRT424830 LRT - SERIES

IKO LRT455020 LRT - SERIES

IKO LRT455240 LRT - SERIES

IKO LRT758525 LRT - SERIES

IKO LRT809025 LRT - SERIES

IKO LRT809054 LRT - SERIES

IKO LRT9510526 LRT - SERIES

IKO LRTZ14016051

IKO LRTZ14016051 LRTZ - SERIES

IKO LRTZ172214 LRTZ - SERIES

IKO LRTZ253018 LRTZ - SERIES

IKO LRTZ283230 LRTZ - SERIES

IKO LRTZ354221 LRTZ - SERIES

IKO LRTZ424830 LRTZ - SERIES

IKO LRTZ606846 LRTZ - SERIES

IKO LRTZ809031 LRTZ - SERIES

IKO LRTZ9511036

IKO LRTZ9511036 LRTZ - SERIES

IKO LRXS-20-C1-H-S2/V - MROSupply.com

IKO LWE20R2500PS2/A2 Slide Unit - MROSupply.com

IKO Machined Type Needle Roller Bearing consists of solid outer ring, rollers and retainer, without inner ring. They are with low sectional height, large load ratings and righty, and most of them come with and without seals. Prepacked lubricant is not provided except double sealed bearings (suffix UU). Proper lubricant must be applied when they are used. Machined Type needle roller bearings are generally used with shafts without inner rings. 0.2?mRa or less shaft surface finish and HRC 58 to 64 shaft hardness are recommended. When these requirements are not possible, use of IKO Inner Rings are recommended.<br><br>