dataSource: amazonScraper (Page 751)

Series CJ2 miniature cylinders available in spring return, spring extend, or double acting offer stainless steel tubing and stainless steel rods. The series is available in bore sizes 6, 10, 16mm and stroke lengths from 1/2in. to 8in.. Mounting options include basic, foot, front flange, and double rear clevis. Series CJ2 is auto switch capable <ul><li>Standard double acting single rod</li><li>Bore sizes: 6, 10, 16 *</li><li>Strokes from 15mm through 200mm depending upon bore size</li><li>Mounts: basic, foot, front flange, double clevis</li><li>Variety of switches and a variety of lead wire lengths</li></ul>

Series CJ5-S is a stainless steel cylinder, designed for use in environments with water spray (such as food processing machines). A special scraper (standard) prevents water from entering the cylinder. Non-toxic additives allow confident use in equipment for food, beverage and medical products, etc. The CJ5-S series can be disassembled for replacement of seals. <ul><li>Stainless steel (SUS304) used for all exterior metal parts</li><li>Standard water resistant scraper prevents liquid leakage into the cylinder</li><li>2 types of sealing material - choices of NBR/FKM (nitrile rubber/fluoro rubber)</li><li>Uses grease for food processing machines - meets FDA standards</li><li>Water-resistant auto switch is available</li></ul>

Series CM2 stainless steel cylinders are compact, lightweight and offer high performance. Improved piston seal and rod seal greatly improve the units life. Rubber bumpers are standard. The CM2 series offers a variety of mounting options and is auto switch capable. <ul><li>Double acting single rod</li><li>Bore sizes: 20, 25, 32, and 40 *</li><li>Strokes from 25mm through 500mm</li><li>Mounts: basic, foot, front and rear flange, clevis, trunnion</li><li>With or without rod boot</li><li>Variety of switches and a variety of lead wire lengths</li></ul>

Series CM2 stainless steel cylinders are compact, lightweight and offer high performance. Improved piston seal and rod seal greatly improve the units life. Rubber bumpers are standard. The CM2 series offers a variety of mounting options and is auto switch capable. <ul><li>Spring extend or spring return</li><li>Bore sizes: 20, 25, 32, and 40 *</li><li>Strokes from 25mm through 250mm</li><li>Mounts: basic, foot, flange, trunnion, clevis</li><li>With or without nylon or heat resistant rod boot, one or both sides</li><li>Variety of switches and a variety of lead wire lengths</li></ul>

Series CRB2, single or double vane type, rotary actuator is available in 10, 15, 20, 30 or 40 bore. The single vane style uses specially designed seals and stoppers which enable this compact type actuator to rotate up to 270. Direct mounting is possible for sizes 10 to 30 with the angle adjuster unit. The use of bearings to support thrust and radial loads, along with the implementation of an internal rubber bumper (except for size 10), makes the CRB2 excellent in reliability and durability. Other options include flange mounting, side or axial ports and auto switch capability.

Series CRB2-Z, single or double vane, rotary actuator is availbable in 10, 15, 20, 30 and 40 bore.  The single vane style use specially designed seals and stoppers which enable this compact type actuator to rotate up to 270 degrees.  Double vane type is standardized for 90 and 100 degrees.<ul><li>Two shaft options available</li><li>Port locations modified</li><li>RoHS compliant</li><li>Mounting position of the auto switch can be set freely</li></ul>

Series CXS is available in six bore sizes and stroke lengths up to 100mm. This series is very compact and has a very accurate non-rotating specification. It is suited for accurate pick-and-place applications or light duty material handling. The CXS can be used with either reed or solid state switches. Available in clean room versions. <ul><li>Dual rod cylinder, compact type</li><li>Slide bearing or ball bushing bearing</li><li>Bore size *: 6, 10, 15, 20, 25, 32</li><li>Standard strokes *: 10, 20, 30, 40, 50, 75, 100</li><li>Auto switches available</li><li>Made to Order additionally released.</li></ul>

Series GX flow indicators have a single clear acrylic cylinder wall and are used to indicate flow or clarity of ultra-pure liquids such as demineralized water. They may also be used with corrosive chemicals that are compatible with acrylic. Plast-O-Matic flow and level indicators are designed to indicate the presence or clarity of liquid in a piping system or to indicate level in a tank. They offer a maximum viewing area with a full 360 degree visibility for dependable observation and inspection from a reasonable distance. With the exception of the Series GX flow indicator, which can only be used for liquids compatible with acrylic, all Plast-OMatic indicators utilize double-wall construction. O-ring seals are used on Series GX indicators allowing them to seal at extremely low pressures as well as high pressures. GX flow indicators are full ported, eliminating any possible flow resistance. Standard fasteners are stainless steel. The transparent outer cylinder wall is high impact strength acrylic. Optional fluttering streamers are corrosion resistant thermoplastic. Made of PVC.

Series ITV electro-pneumatic and electronic vacuum regulators control air/vacuum pressure steplessly in proportion to an electric signal. They are light weight in design with a bright and easy to read LED display. The monitor output is available eit

Series KP are one-touch fittings for clean room blow-off systems and drive air systems. The KP series is completely oil free and liquid-contact areas are non-metallic. Parts are cleaned, assembled and double packaged in a clean room. Resin parts for one-touch series KPQ/KPG (for drive system air piping) are polypropylene.<ul><li>Clean One-touch fittings</li><li>For drive system air piping</li><li>M5 size standardized</li><li>Resin parts are polypropylene</li><li>KPQ: Brass (electroless nickel plated)</li><li>KPG: Stainless Steel (SUS304)</li></ul>

Series KQG is a one-touch fitting made of all stainless steel SUS316, except seal parts. The series is suitable for use with steam and is grease-free. Applicable tubing includes FEP, PFA, nylon, soft nylon, polyurethane and polyolefin. The KQG series is available in both metric and inch sizes.<ul><li>Stainless steel 316 one-touch fittings, inch</li><li>Seal parts:  FKM</li><li>Can be used with steam</li><li>Grease-free</li><li>Applicable tubing material includes FEP, PFA, nylon, soft nylon, polyurethane, polyolefin</li></ul>

Series KQG2 is a one-touch fitting made of all stainless steel SUS316, except seal parts. The series is suitable for use with steam and is grease-free. Applicable tubing includes FEP, PFA, nylon, soft nylon, polyurethane and polyolefin. The KQG2 series is available in both metric and inch sizes. The KQG2 is more compact and lightweight, and offers more configuration variations and tube sizes than the KQG series.<ul><li>Stainless steel 316 one-touch fittings, inch size</li><li>Seal parts: FKM </li><li>Can be used with steam </li><li>Grease-free </li><li>Applicable tubing material includes FEP, PFA, nylon, soft nylon, polyurethane, polyolefin</li></ul>

Series LVM is a compact, direct acting, 2/3 port solenoid valve for chemicals. The unique construction reduces residual liquid to a minimum. Superior resistance to chemicals requires less maintenance. Service life (based on SMC test conditions) is 1

Series M and MS miniature fittings are for use with air connections in confined areas. The hose nipple and hose elbow styles accept nylon, soft nylon and polyurethane tubing. The body of the MS series is stainless steel, making it possible to use this fitting in corrosive applications.<ul><li>Miniature fittings for use with TU miniature tubing</li><li>Applicable tube material: polyurethane</li><li>Applicable tube diameter: 2/ 1.2</li><li>Available in 4 types: barb, barb elbow, barb one-touch, reducer</li><li>Maximum operating pressure (at 20?C): 1MPa</li></ul>

Series M and MS miniature fittings are for use with air connections in confined areas. The hose nipple and hose elbow styles accept nylon, soft nylon and polyurethane tubing. The body of the MS series is stainless steel, making it possible to use this fitting in corrosive applications.<ul><li>Simple connection/disconnection</li><li>High retaining force</li><li>Miniature size</li><li>Accepts many styles of plastic tubing</li></ul>

Series M and MS miniature fittings are for use with air connections in confined areas. The hose nipple and hose elbow styles accept nylon, soft nylon and polyurethane tubing. The body of the MS series is stainless steel, making it possible to use this fitting in corrosive applications.<ul><li>Stainless steel material (SUS316)</li><li>Simple connection/disconnection</li><li>Compact size for tight piping areas</li><li>Accepts many styles of plastic tubing</li></ul>

Series MGF guide tables are low profile, compact cylinders which utilize a large concentric guiding sleeve to provide excellent eccentric load resistance. Mounting is possible from 2 directions. A built-in non-rotating mechanism prevents rotation of the table top. T-slots are provided on 3 faces of the MGF body *, allowing mounting of various brackets. Optional auto switches can be mounted on 4 faces of the body.<ul><li>Low-profile, compact, guide table </li><li>Large diameter guide rod enables cylinder to handle eccentric loads applied from any direction within a 360<span style="in.FONT-FAMILY:" times="" new="" roman,serif;="" font-size:="" 10pt;="" mso-fareast-font-family:="" roman;="" mso-ansi-language:="" en-us;="" mso-fareast-language:="" mso-bidi-language:="" ar-sain.=""> angle </li><li>Available in 40, 63 or 100mm bore sizes </li><li>Auto switch capable</li></ul>

Series Miles Nimbus PG pag-based formulation provides excellent wear protection, enhanced fluid life, and superior carbon and varnish control. Attributes excellent dispersant properties pag-based formulation excellent lubricity very high film strength outstanding carbon and varnish control excellent fluid life enhanced resistance against water contamination excellent protection against wear, rust and corrosion reduced maintenance costs and downtime non-toxic/non-hazardous typical properties: Nimbus pg-680 viscosity Index 272 viscosity cSt @ 40?c 648 viscosity cSt @ 100?c 112.9 Flash point ?F 480 auto-ignition point ?F 740 pour point ?F -20 FZG pass stage 12+ copper corrosion, 24 hr. 1B.

Series Miles SB Comp oil Plus synthetic blend Plus compressor lubricants are premium fluids blended from the finest materials available. They have been proven in millions of horsepower hours. Series Miles SB Comp oil Plus compressor lubricants give outstanding service?even in moderately severe operating conditions. Attributes long fluid life with enhanced thermal and oxidative stability excellent protection against wear, rust and corrosion reduced maintenance costs and downtime excellent resistance against water contamination non-toxic/non-hazardous typical properties ISO grade 100 viscosity cSt @ 0?c 2276 viscosity cSt @ 40?c 150 viscosity cSt @ 80?C 30.1 viscosity cSt @ 90?c 22.4 viscosity cSt @ 100?c 17.1 Flash point ?F 517 auto-ignition point ?F 839 pour point ?F -15 four ball, 40 kg, 1200 RPM, 167?f 1 hr., scar DIA mm .44 four ball weld point, kg 100 copper corrosion, 24 hr. 1a,demulsibility, 130?f, 30 min 40/40/0.

Series Miles syn-gear use HD is designed for heavy-load and high-temperature applications and formulated with enhanced extreme-pressure (EP) additives. Series Miles syn-gear use HD provides excellent protection and a long fluid life ? even in the most demanding applications and environments. Attributes excellent lubricity very high film strength outstanding carbon and varnish control excellent fluid life excellent dispersant properties enhanced resistance against water contamination excellent protection against wear, rust and corrosion reduced maintenance costs and downtime non-toxic/non-hazardous lubrication properties Miles syn-gear use hd-460 viscosity Index 199 viscosity cSt @40?c 415.0 viscosity cSt @100?c 54.5 Flash point ?F 527 auto-ignition point ?F 845 pour point ?F -15 Timken OK load, kg 40 copper corrosion, 24 hr. 1B demulsibility, 130?c, 30 min 40/37/3.

Series MXQR, reversible air slide table, uses a recirculating linear guide for high rigidity and high precision.  Ports on the MXQR can easily be reversed on site, with an allen wrench, to suit installation conditions.The MXQR is interchangeable with the MXQ air slide table, as the body and workpiece mounting dimensions are the same.  MXQR expands from MXQ s shock options to include a new shock for the 6mm bore, as well as RJ shocks for shorter cycle times and lower energy loads.<ul><li>Air slide table w/built-in guide rail</li><li>Bore size (mm): 6, 8, 12, 16, 20, 25</li><li>Reversible Type</li><li>Adjuster options: rubber stopper, shock absorber, metal stopper</li><li>Auto switch capable</li></ul>

Series NCA1 medium duty tie rod cylinders are NFPA interchangeable, have a crimped piston rod assembly, are pre-lubricated and available in 11 mounting styles. Bore sizes range from 1.5 to 4 inches. The NCA1 expanded line of medium duty cylinders offer bore sizes ranging from 5 to 8 inches, and come standard with adjustable air cushion.<ul><li>5in. bore medium duty air cylinder</li><li>11 NFPA mounting options</li><li>Standard with adjustable air cushion</li><li>Auto switch capable</li></ul>

Series NCJ2 miniature cylinders available in spring return, spring extend, or double acting all offer stainless steel tubing and stainless steel rods. Available in bore sizes 6, 10, 16mm and stroke lengths from 1/2in. to 8in.. Basic, foot, front flange and double rear clevis mounting options. Auto-switch capable. Other features include non-rotating, double rod, rubber bumpers and a stainless steel body.<ul><li>Standard type, double acting, single rod</li><li>Bore sizes: 1/4in. *, 3/8in. *, 5/8in. *</li><li>Standard strokes from 1/2in. to 8in.</li><li>Auto switch capable</li></ul>

Series NCM stainless steel cylinder offers space savings, high performance, and interchangeability with other stainless steel cylinders. A wear ring extends the seal life and a bronze rod bushing is standard on all bore sizes. The NCM is available in 4 mounting styles * as well as double rod and spring return or spring extend models. The NCM is auto-switch capable without any change in cylinder dimension. Bore sizes range from 7/16in. to 2in. and standard strokes from 1/2in. to 12in.. <ul><li>Direct mount, double acting, single rod air cylinder</li><li>Stainless steel body</li><li>Bore sizes: 3/4in., 1 1/16in., 1 1/2in.</li><li>Auto switch capable</li></ul>

Series NCM stainless steel cylinder offers space savings, high performance, and interchangeability with other stainless steel cylinders. A wear ring extends the seal life and a bronze rod bushing is standard on all bore sizes. The NCM is available in 4 mounting styles * as well as double rod and spring return or spring extend models. The NCM is auto-switch capable without any change in cylinder dimension. Bore sizes range from 7/16in. to 2in. and standard strokes from 1/2in. to 12in.. <ul><li>Double acting single rod </li><li>Bore sizes *: 7/16, 9/16, 3/4, 7/8, 1 1/16,1 1/4, 1 1/2, 2 </li><li>Mounts: nose, rear, end, rod, block </li><li>Variety of switches and lead wire lengths</li><li>Optional Rod Boot </li></ul>

Series NCM stainless steel cylinder offers space savings, high performance, and interchangeability with other stainless steel cylinders. A wear ring extends the seal life and a bronze rod bushing is standard on all bore sizes. The NCM is available in 4 mounting styles * as well as double rod and spring return or spring extend models. The NCM is auto-switch capable without any change in cylinder dimension. Bore sizes range from 7/16in. to 2in. and standard strokes from 1/2in. to 12in.. <ul><li>Double rod type air cylinder</li><li>Stainless steel rod</li><li>Bore sizes-3/4in. to 2in.</li><li>3 mounting types available</li><li>Auto switch capable</li></ul>

Series NCM stainless steel cylinder offers space savings, high performance, and interchangeability with other stainless steel cylinders. A wear ring extends the seal life and a bronze rod bushing is standard on all bore sizes. The NCM is available in 4 mounting styles * as well as double rod and spring return or spring extend models. The NCM is auto-switch capable without any change in cylinder dimension. Bore sizes range from 7/16in. to 2in. and standard strokes from 1/2in. to 12in.. <ul><li>Single acting single rod, spring return or spring extend </li><li>Bore sizes *: 3/4, 7/8, 1 1/16, , 1 1/4, 1 1/2 </li><li>Maximum stroke: up to 6in. as standard </li><li>Available with auto switches</li></ul>

Series S070 is a super compact direct acting 2/3 port solenoid valve that meets the miniaturization needs of analyzers, medical equipment and semiconductor manufacturing equipment. S070 is extremely lightweight (5g for valve single unit type) and operation noise is 38dB(A) or less. It is easy to increase or decrease the number of stations (stacking base). Valve width is 7mm. <ul><li>3 port solenoid valve, direct operated</li><li>Valve width: 7mm</li><li>Weight: 5g (single unit valve)</li><li>Operation noise: 38dB(A) or less</li><li>Power consumption: 0.35W (std), 0.1W (w/power saving circuit)</li></ul>

Series SY offers major advances in valve performance for cost-effective solutions to your requirements. The series offers high flow with low power consumption in a compact design. The SY is available in body ported or base mounted styles and can be used individually or manifold mounted.<ul><li>Fluid: air </li><li>Operating pressure range: (internal pilot) 0.1 - 0.7MPa (external pilot) -100kPa to 0.7MPa (external pilot, pilot pressure range) 0.25 - 0.7MPa </li><li>Effective area mm 2 (Cv): body ported 10.6 (0.59); base mounted 12.6 (0.7) </li><li>Coil rated voltage: 3, 5, 6, 12, 24VDC; 100, 110, 200, 220VAC </li><li>Response time (0.5MPa) w/o indicator light andamp; surge voltage suppressor: 32ms or less </li><li>Ambient andamp; fluid temperature: 50C </li></ul>