Fully threaded CD-weld studs are suitable for fastening applications where male threads are needed for the full fastener length. They have a small projection that melts and fuses to the workpiece surface during welding, helping ensure usable threads extend to the top of the installed studs. CD-weld threaded studs are fasteners with a small projection, or pip, on the base that melts and bonds to the surface of the workpiece to create a permanent male thread. Also called capacitor discharge welds, they require lower levels of heat and less time to weld than other weld-mount studs, making them a good choice for thin, lightweight materials that should avoid excessive heating to prevent distortion. They are also suitable for applications that don't have room for a bottom- or top-projection weld stud. This listing is for pkg. of 1, 000. Technical Specification Item Mountable Threaded Stud Mountable Stud Type CD Weld Weld Stud Type Fully Threaded System of Measurement Inch Threaded Rod Material Steel Threaded Rod Finish Copper Plated Thread Size 8-32 Stud Length 3/4 Base Dia. 1/4 Thread Direction Right Hand Threaded Rod Thread Type UNF Meets/Exceeds ASTM A29, ASTM A108 Min. Tensile Strength 50, 000 psi Thread Class 2A Yield Strength 35, 000 psi
Fuse, 5A Fuse Amps, Nonindicating, Mda Series, 250Vac Voltage Rating, Time Delay, Single Element, Body Material Ceramic, Nonrejection, Body Style Cylindrical, Interrupt Rating 200A At 250Vac, 10Ka At 125Vac, Length 1-1/4 In., Diameter 1/4 In., Functionally Equal To Mersen/Ferraz Shawmut Gsa, Littelfuse 326, Standards Ce, Ul 248-14 Guide Jdyx, Csa Certification Class 1422-01, Package Quantity 5
Fuse, 6 Amp, No indicating, AGX Series, 125VAC Voltage Rating, Fast Acting, Single Element, Body Material: Glass, Rejection, Body Style: Cylindrical, Interrupt Rating: 1kA at 125VAC, Length 1 In., Diameter 1/4 In., Functionally Equal To Bussmann MMB, Mersen/Ferraz Shawmut GGX, Little fuse 361, 362, Standards CE, UL 248-14 Guide JDYX2, CSA Certification Class 1422-01. Pack of 100.
G2 Satellite Compass - NMEA 2000 with 6M CableAccurate Heading & Precise Position for ProfessionalsFeatures:Supports both GPS and GLONASS satellites for complete redundancyHeading accuracy < 0.25? rmsPosition accuracy < 0.3m 95% confidence (DGPS)An integrated 9 Axis Inertial Measurement Core (IMC technology) provides enhanced roll, tilt and heading stability even during momentary loss of satellite signalsIMO Compliant G3 color display system (optional)Engineered enhancements to exceed sealed IP67 ratingExtended 2 year warrantyNMEA 2000? interfaceType approved as primary heading AND positioning deviceHeave, Pitch, Roll and Rate of Turn as standard outputHeading updates 1 to 20 HzBAUD Rate selectable: 4800, 9600, 19200, 38400,115200Fully compatible with on board NMEA 0183 and NMEA 2000? RADAR, ECDIS, AIS, Cameras, SONAR, PC and AutopilotsCompact integrated surface mounting (Pole mount optional)IMO Compliant, Wheelmark and USCG approvedPre-programmed default settings for Heading, Rate of Turn, Course over Ground, Lat/Long position, Time & Date1PPS output standard15 meter serial cable standard (30 meter optional)6 meter NMEA 2000? Cable (Optional)CE certified for EMI and RFI immunityWorldwide service Owner's Manual (pdf)
Galvanized panels are 12 gauge. Panel with any side over 20.00" has 3/4" flange on all sides. Optional "G" panels have a conductive finish (no paint). Panels fit the following enclosures: NEMA 1, Large (NIC); NEMA 3R, hinged Cover (RHC, Large); NEMA 4, 412, & 4X Single Door (N12, N4, N412, SSN4, SSN43PT, SSN43PTW); NEMA 12, 2-Door Wall-Mount (WAWF), Single Door; Right Flange Disconnect (SDN12, ABM12); Large JIC (B-CH, Large) Single door N12.